17 relations: Buck–boost converter, Capacitor, Common base, Common drain, Common source, DC-to-DC converter, H bridge, Inductance, LC circuit, MOSFET, Power inverter, Push–pull output, Rectifier, Remanence, Switched-mode power supply, Transformer, Volt.
Buck–boost converter
The buck–boost converter is a type of DC-to-DC converter that has an output voltage magnitude that is either greater than or less than the input voltage magnitude.
New!!: Push–pull converter and Buck–boost converter · See more »
Capacitor
A capacitor is a passive two-terminal electrical component that stores potential energy in an electric field.
New!!: Push–pull converter and Capacitor · See more »
Common base
In electronics, a common-base (also known as grounded-base) amplifier is one of three basic single-stage bipolar junction transistor (BJT) amplifier topologies, typically used as a current buffer or voltage amplifier.
New!!: Push–pull converter and Common base · See more »
Common drain
In electronics, a common-drain amplifier, also known as a source follower, is one of three basic single-stage field effect transistor (FET) amplifier topologies, typically used as a voltage buffer.
New!!: Push–pull converter and Common drain · See more »
Common source
In electronics, a common-source amplifier is one of three basic single-stage field-effect transistor (FET) amplifier topologies, typically used as a voltage or transconductance amplifier.
New!!: Push–pull converter and Common source · See more »
DC-to-DC converter
A DC-to-DC converter is an electronic circuit or electromechanical device that converts a source of direct current (DC) from one voltage level to another.
New!!: Push–pull converter and DC-to-DC converter · See more »
H bridge
An H bridge is an electronic circuit that enables a voltage to be applied across a load in opposite direction.
New!!: Push–pull converter and H bridge · See more »
Inductance
In electromagnetism and electronics, inductance is the property of an electrical conductor by which a change in electric current through it induces an electromotive force (voltage) in the conductor.
New!!: Push–pull converter and Inductance · See more »
LC circuit
An LC circuit, also called a resonant circuit, tank circuit, or tuned circuit, is an electric circuit consisting of an inductor, represented by the letter L, and a capacitor, represented by the letter C, connected together.
New!!: Push–pull converter and LC circuit · See more »
MOSFET
MOSFET showing gate (G), body (B), source (S) and drain (D) terminals. The gate is separated from the body by an insulating layer (white). surface-mount packages. Operating as switches, each of these components can sustain a blocking voltage of 120nbspvolts in the ''off'' state, and can conduct a continuous current of 30 amperes in the ''on'' state, dissipating up to about 100 watts and controlling a load of over 2000 watts. A matchstick is pictured for scale. A cross-section through an nMOSFET when the gate voltage ''V''GS is below the threshold for making a conductive channel; there is little or no conduction between the terminals drain and source; the switch is off. When the gate is more positive, it attracts electrons, inducing an ''n''-type conductive channel in the substrate below the oxide, which allows electrons to flow between the ''n''-doped terminals; the switch is on. Simulation result for formation of inversion channel (electron density) and attainment of threshold voltage (IV) in a nanowire MOSFET. Note that the threshold voltage for this device lies around 0.45 V The metal-oxide-semiconductor field-effect transistor (MOSFET, MOS-FET, or MOS FET) is a type of field-effect transistor (FET), most commonly fabricated by the controlled oxidation of silicon.
New!!: Push–pull converter and MOSFET · See more »
Power inverter
A power inverter, or inverter, is an electronic device or circuitry that changes direct current (DC) to alternating current (AC).
New!!: Push–pull converter and Power inverter · See more »
Push–pull output
A push–pull amplifier is a type of electronic circuit that uses a pair of active devices that alternately supply current to, or absorb current from, a connected load.
New!!: Push–pull converter and Push–pull output · See more »
Rectifier
A rectifier is an electrical device that converts alternating current (AC), which periodically reverses direction, to direct current (DC), which flows in only one direction.
New!!: Push–pull converter and Rectifier · See more »
Remanence
Remanence or remanent magnetization or residual magnetism is the magnetization left behind in a ferromagnetic material (such as iron) after an external magnetic field is removed.
New!!: Push–pull converter and Remanence · See more »
Switched-mode power supply
A switched-mode power supply (switching-mode power supply, switch-mode power supply, switched power supply, SMPS, or switcher) is an electronic power supply that incorporates a switching regulator to convert electrical power efficiently.
New!!: Push–pull converter and Switched-mode power supply · See more »
Transformer
A transformer is a static electrical device that transfers electrical energy between two or more circuits through electromagnetic induction.
New!!: Push–pull converter and Transformer · See more »
Volt
The volt (symbol: V) is the derived unit for electric potential, electric potential difference (voltage), and electromotive force.
New!!: Push–pull converter and Volt · See more »
Redirects here:
Push pull converter, Push-Pull Converter, Push-pull converter.